Massive power, portability and versatility you can use with your favorite cab
The Microtubes 900 is a 900W amplifier equipped with an all analog preamplifier and a Class D Power Module. The first thing you will notice from the Microtubes 900 is its unusual control layout: On the right side you’ll find the clean section which is the foundation of your tone. It features Gain and Master controls an active 4 band EQ. Along with Low and Treble controls you will find Low Mids and Hi Mids control, each knob with their own 3-way frequency switch. On the left side you will find the Microtubes Engine which acts as an extra channel that can bring your clean tone to the next level by helping you cut through the mix while adding anything from subtle tube break up, harmonics and natural compression to obliterating distortion. Intelligent Footswitch The Intelligent Footswitch is an intuitive yet versatile accessory for your Microtubes 900. One tap will engage and disengage the Microtubes Engine, while holding for 3 seconds will Mute the amplifier. It is connected to the head via a standard 1/4-in. cable and it's powered by a microcontroller that sends commands to the head using a proprietary communication protocol. Spec and Tech Input: Connect your instrument via a standard 1/4-in. mono cable. Passive/Active: Switch from passive to active mode. Some active basses can have a hotter signal output which can make the amp distort early (feel free to use it on Passive move even with active basses if such additional distortion is desired). Microtubes: Turns on or off the Microtubes Engine to add natural compression, organic harmonic enhancement, and saturation ranging from mild overdrive to high gain bass rage. The Microtubes Engine operates before the clean section (you can therefore use the 4 Band Active EQ for additional tone shaping in addition to the Tone knob described below). Drive: Controls the amount of distortion that the Microtubes Engine will deliver. It will change from a soft warm overdrive to a massive modern distorted tone. Tone: Controls the high harmonic content of the Microtubes Engine via a variable low pass filter: crank it up for additional attack and definition or dim it down for a smoother sound. This is handy if running bright clean EQ settings or cabinets with tweeters. Level: Controls the Microtubes Engine’s output volume. Blend: Mixes between the Clean signal and the Distortion signal (Microtubes Engine). B3K/VMT: Selects between two overdrive voicings: B3K mode will deliver an aggressive, percussive sound while the VMT will bring up the mids for a warmer, more neutral character. Gain: Changes the volume of the signal the Active 4 Band EQ. You can set it low prior to ensuring the cleanest operation possible or set it higher for more aggressive growl. Bass: +-12dB at 80Hz. Changes the low content of the signal. Low Mids: +-12dB of the selected frequency via the LOW MIDS switch (described below). Changes the lower mid content of the signal. Low Mids: Use this switch to change the frequency of the low mid band from 250Hz, 500Hz or 1kHZ. Hi Mids: +-12dB of the selected frequency via the HI MIDS ƒ switch (described below). Changes the higher mid content of the signal. Hi Mids: Use this switch to change the frequency of the hi mid band from 750Hz, 1.5kHz and 3kHZ. Treble: +-12dB at 5kHz. Changes the high content of the signal. Master: Controls the overall volume of the amplifier. Mute: Mutes the amplifier.
Speaker Output: Connects the amplifier to your cabinet. This Speakon combo jack allows for either Speakon or 1/4 in. speaker cable operation. *WARNING: Do not use an instrument cable with this jack. Using an instrument cable can damage your amplifier. Min-Load: Press when using a 2-ohm load. You can use this control to lower the output if your 4-ohm cabinet is not able to handle more than 500W (you can also get 350W with an 8-ohm cabinet in this configuration). Pre Amp Out: This output connects the preamp to a different power amp. Power Amp In: Use this input to connect a different preamp to the power amp. (master volume will be disabled) Post-Pre: Selects what signal will be delivered by the DI output. Selecting PRE, sends a clean copy of your input bass signal. Selecting POST delivers a signal processed by the preamp of the amp (gain, distortion, eq, master, etc.) Ground Lift: Lifts the ground of the DI XLR output. If a ground noise in you DI signal is experienced, try changing the setting of this control. Balanced Output: Connects the Microtubes 900 preamplifier to balanced equipment (mic preamp, console, recorder, compressor, audio interface, etc.) via a standard XLR jack.
Footswitch The Footswitch allows you to remotely engage and disengage the Microtubes Engine. Hold the footswitch to Mute the amplifier. The VMT/B3K push button will remain operational with the Intelligent Footswitch plugged in. -Use a regular mono instrument cable to connect the amplifier to the footswitch. -Remove the cable from the footswitch jack in the rear panel if you want to control the amp from the front panel.
- Power: 900 watts
- Two channels
- Single input
- Impedance: 2, 4, 8 ohms
- Controls: 4-band EQ, gain, master, overdrive select, mid select
- DI output with pre-/post- switch
- Footswitch included
- Dimensions: 10.5 in. x 9.05 in. x 2.52 in.
Following checkout you will receive a Paypal invoice if your order is in stock or readily available with the manufacturer. Your Paypal account , credit card or debit card will not be charged if your order is not in stock or available with the manufacturer. In stock orders are shipped within 1-2 business days (FEDEX tracking details provided). Un-stocked orders require a special order from the manufacturer and ship within 7-10 business days.
To ensure 100% customer satisfaction , we offer a 14 day return policy and price matching. Our knowledgeable staff are here to help with queries you may have about the , prices in Singapore , stock availability etc. We will help you to select from the best products available. Contact our experts to find the best product to suit your style or request more information about the .
- Buy products with confidence.
- We ship to all major regions in Singapore.
- Return to base repair or replacement (1 Year return to base).
- Please contact us for detailed information about our terms , conditions and warranty.
AudioBuy Singapore ship all stocked orders Monday to Friday. All online orders are carefully packed and insured before dispatch. Our customers are very important to us and we will work with you until final delivery to ensure you're completely satisfied.
|Condition||Sealed / New|
Contact us for stock availability , price quotes , expedited shipping quotes or to arrange a return of your (for the full purchase price of ). You may return most new, unopened items within 30 days of delivery for a full refund. AudioBuy are very proud to carry a large selection of gear. You demand quality, reliability, and innovative design from your gear, and we're here to help you find exactly what you need. We're glad to answer any questions you have and you can always depend on AudioBuy to give you the best possible value on musical instruments and accessories with responsive customer service.